I spent two hours tonight to prepare the parts for the wing tip. Mainly deburring of edges and holes of the skins. I also marked the cut out for the nav light and cut it out. I used a #19 drill to start a hole, widened it with the step drill (all the way through) and then used the nibbler to roughly cut out the hole. Fine trimming was done with the angle die grinder and a pink die. This resulted in large burrs that I removed with a file and smoothed the edges with a 1" Scotchbrite wheel. Turned out to be pretty good - yet I forgot to take a photo. I'll add that when I get back from work tomorrow.
By the way, I've noticed something funny about the Lighting Kit. As it was one of the optional kits coming out way after the all the other kits, the manual is laid out for adding it to an already built RV-12. Now, that I am adding it while I go, I could do it much easier and faster but as I don't have a manual describing this approach I have to read section 40 and fully understand what the purpose of each step is and apply it to my situation. This takes significantly more time and voids the advantage of adding it during the build completely. I wish there were two sets of manuals available. One for adding it later and one for adding it during the build with updated pages for the sections.
Tomorrow night I will probably start the surface prep on the wing tip parts as I finished all the deburring tonight.
Monday, November 8, 2010
Just a Little Deburring...
Sunday was my day off from building, but I guess you know me enough by now to know that I still had to do at least a little something. And that little something was taking that ugly concave hatch off and bend it to shape. It now blends in with the curve of the wing just perfectly. I let it off for now though as I want to prime the inside with the next stack of aluminum.
The other thing I was doing was getting ready for working on the wing tip. The bigger sheets had already been primed but there area handful of small parts that I hadn't touched yet. So I retrieved them and started the deburring process on the holes and edges. I also bent the outboard wing handle insert for both wings and started to wonder how I am going to get paint evenly sprayed into that hole they are going to create...
The rest of the day I was busy assembling all the new "toys" I bought at HF. Among them a workbench that I mounted the 6" Scotchbrite grinder on to get it out of the work shop and with it all the dust it creates when I use it. It's now outside in front of the work shop and needs much less clean up after a deburring session as the wind is taking care of what I had to do with a vacuum before.
As outlook for this week. It appears that I will focus on finishing the wing tip and get the nav light installed as well. I hope to be able to completely finish off the left wing and put it in the wing cradle. I am not sure how to celebrate this major construction step when I accomplish it. Any ideas what to do???
The other thing I was doing was getting ready for working on the wing tip. The bigger sheets had already been primed but there area handful of small parts that I hadn't touched yet. So I retrieved them and started the deburring process on the holes and edges. I also bent the outboard wing handle insert for both wings and started to wonder how I am going to get paint evenly sprayed into that hole they are going to create...
The rest of the day I was busy assembling all the new "toys" I bought at HF. Among them a workbench that I mounted the 6" Scotchbrite grinder on to get it out of the work shop and with it all the dust it creates when I use it. It's now outside in front of the work shop and needs much less clean up after a deburring session as the wind is taking care of what I had to do with a vacuum before.
As outlook for this week. It appears that I will focus on finishing the wing tip and get the nav light installed as well. I hope to be able to completely finish off the left wing and put it in the wing cradle. I am not sure how to celebrate this major construction step when I accomplish it. Any ideas what to do???
Saturday, November 6, 2010
Left Wing Almost Done
So I went back to the wing doubler that I had left in the evening. The fit was really off and I decided to remove it. After reading a bit about other experiences with the doubler on the Van's Airforce Forum I decided to work around the problem of the pre-dimpled holes by clamping the doubler in a vise with wood as a buffer and bent it right behind the line of rivet holes, about 3/8" from the edge. This worked pretty well and a visible crease was created that ensured that once the rivets were set, the edge would still be in touch with the skin.


So I went on clecoed the doubler back in place and also got ready to finish the rest of the nose skins.

The riveting didn't take a lot of time and soon the wing looked like this:

Now it was time to turn the wing over again and get the inspection hatch installed. 10 nutplates had to get prepared and riveted in. A bit less than an hour later the hatch was installed.

That's how I left it. The wing would fly right now although the outboard area sure wouldn't look good. So, I'm not quite done just yet, but almost there.
BTW: Later I noticed that I will have to remove the hatch again and do some more work on it. It is currently slightly bulging inside and I want to bend it to follow the shape of the wing more. I might have to add a stiffener on the back if it wouldn't stay in its shape. Currently it just doesn't look nice.
So I went on clecoed the doubler back in place and also got ready to finish the rest of the nose skins.
The riveting didn't take a lot of time and soon the wing looked like this:
Now it was time to turn the wing over again and get the inspection hatch installed. 10 nutplates had to get prepared and riveted in. A bit less than an hour later the hatch was installed.
That's how I left it. The wing would fly right now although the outboard area sure wouldn't look good. So, I'm not quite done just yet, but almost there.
BTW: Later I noticed that I will have to remove the hatch again and do some more work on it. It is currently slightly bulging inside and I want to bend it to follow the shape of the wing more. I might have to add a stiffener on the back if it wouldn't stay in its shape. Currently it just doesn't look nice.
Friday, November 5, 2010
Left Top Skins Riveted
I finished riveting the top skins as soon as I got home from work. There weren't that many rivets left and I had them already seated last night so all I had to do was starting the riveting fun.
Then I tried to put the wing doubler in place. I noticed immediately that the rolled edge at the front that I had put on wasn't rolled strongly enough to make for a nice fit with the wing, so I took it off. Increasing the roll, flattened the dimples on the pre-dimpled holes, so I had to re-dimple them. Also the dimples make it really tricky to break that edge effectively and evenly. In this case I'd really wish Van's hadn't done so much prep work for me. It would have been much easier to break the edge with undimpled holes and then just dimple them myself.
For now I'm almost ok with the roll. Only the most inner hole seems to have an edge that is not well aligned to the wing. I think I can adjust this without taking the whole doubler off, but this will be tricky and I want to do this when I'm fresh, so I just clecoed the doubler in place and let it be.

I also clecoed the rest of the nose skins in place and seated the rivets on all the left over holes - minus the ones I should leave open for now.
Then I tried to put the wing doubler in place. I noticed immediately that the rolled edge at the front that I had put on wasn't rolled strongly enough to make for a nice fit with the wing, so I took it off. Increasing the roll, flattened the dimples on the pre-dimpled holes, so I had to re-dimple them. Also the dimples make it really tricky to break that edge effectively and evenly. In this case I'd really wish Van's hadn't done so much prep work for me. It would have been much easier to break the edge with undimpled holes and then just dimple them myself.
For now I'm almost ok with the roll. Only the most inner hole seems to have an edge that is not well aligned to the wing. I think I can adjust this without taking the whole doubler off, but this will be tricky and I want to do this when I'm fresh, so I just clecoed the doubler in place and let it be.
I also clecoed the rest of the nose skins in place and seated the rivets on all the left over holes - minus the ones I should leave open for now.
Thursday, November 4, 2010
A Little Bit of RIveting...
... goes a long way, if you do it every night. So I'm going forward with the little time I have in the evening spending it working on the left wing.
I finished riveting the outboard skin that I had left yesterday and I also pulled the rivets on the center skin.

Then it was time to remove the remaining clecos and get ready for the last chapter by seating the rivets on the now vacated holes.

That was about the time when I thought it'd be better to get some rest for a change as I wouldn't have been able to pull all of them tonight anyway. Leaving some of the fun for tomorrow.
One hour of riveting and clecoing spent brought me to 292 hrs spent so far and 34.5 hrs on section 17 so far.
I finished riveting the outboard skin that I had left yesterday and I also pulled the rivets on the center skin.
Then it was time to remove the remaining clecos and get ready for the last chapter by seating the rivets on the now vacated holes.
That was about the time when I thought it'd be better to get some rest for a change as I wouldn't have been able to pull all of them tonight anyway. Leaving some of the fun for tomorrow.
One hour of riveting and clecoing spent brought me to 292 hrs spent so far and 34.5 hrs on section 17 so far.
Wednesday, November 3, 2010
Hedgehogmania
I was putting on the top skins tonight. Instead of going one by one and putting in and removing the clecos for the overlapping skins, I just threw 'em all on at once. That certainly was calling for some extended cleco time. It took me 45 minutes to just cleco all three skins down and another hour to just seat all the rivets in the left open holes.

This was followed by almost an hour of riveting and all I got done was pulling the rivets on the inboard and almost all on the outboard skin. I didn't even get to the second run after removing clecos. Wow, I wasn't aware just how many rivets there are in the wing!
And my wife correctly commented by saying: "And just the same amount again for the other wing". Ouch!

This one's a bit blurry but the only one I got. I try to do a better one tomorrow...
This was followed by almost an hour of riveting and all I got done was pulling the rivets on the inboard and almost all on the outboard skin. I didn't even get to the second run after removing clecos. Wow, I wasn't aware just how many rivets there are in the wing!
And my wife correctly commented by saying: "And just the same amount again for the other wing". Ouch!
This one's a bit blurry but the only one I got. I try to do a better one tomorrow...
Tuesday, November 2, 2010
Flaperon Hinges Installed
I wanted to get a lot done tonight and I did put my time down but it doesn't really show. At least that's my perspective on the results of tonight's riveting session.
I started clecoing the nose section of the left wing to rivet the first 5 rows of rivets (and the ones that were left open on the bottom).

That took some time and then the riveting was really slow as I didn't want to set more than just one rivet at a time per rivet line. The tension on the nose skins is quite high and in order to get a good positioning I needed a lot of clecos holding it down and go one hole at the time. Then all those clecos had to be removed again. Why, I'm not so sure. The manual told me to and I obeyed. Now that I think about it I probably will have to put them back in again when I finish the rivet lines. Weird.

The next step was to put in the flaperon hinges for the middle and the outboard side of the wing. That was a pretty tricky assembly. Reading the long paragraph in the manual I had the impression that it was overly complicated and I tried my own approach. That was to put in the hinge rib and the hinge itself all at the same time, holding it together with clecos.
Let me tell you, that you'll have a hard time to just seat the rivets that way. You might be tempted to tap drill the holes which will widen them and you might lose the tight fit this assembly is asking for.
I analyzed my approach and gave up. Then I followed the manual meticulously and the result was a perfect tight fit. Seating and squeezing the rivets on these hinges is a bit tricky and you will need to use the close quarter riveter which just barely fit in.

This is the hinge in the middle of the wing. The dark green spots are from primer to cover up nicks from the manual riveter and to cover up the rivets themselves (while I was at it).

Finally I put the top skins in place to see how the wing looks like and also to cover the interior from excessive dust (there's another storm forecast for tomorrow).
Looks almost like a wing now!
I started clecoing the nose section of the left wing to rivet the first 5 rows of rivets (and the ones that were left open on the bottom).
That took some time and then the riveting was really slow as I didn't want to set more than just one rivet at a time per rivet line. The tension on the nose skins is quite high and in order to get a good positioning I needed a lot of clecos holding it down and go one hole at the time. Then all those clecos had to be removed again. Why, I'm not so sure. The manual told me to and I obeyed. Now that I think about it I probably will have to put them back in again when I finish the rivet lines. Weird.
The next step was to put in the flaperon hinges for the middle and the outboard side of the wing. That was a pretty tricky assembly. Reading the long paragraph in the manual I had the impression that it was overly complicated and I tried my own approach. That was to put in the hinge rib and the hinge itself all at the same time, holding it together with clecos.
Let me tell you, that you'll have a hard time to just seat the rivets that way. You might be tempted to tap drill the holes which will widen them and you might lose the tight fit this assembly is asking for.
I analyzed my approach and gave up. Then I followed the manual meticulously and the result was a perfect tight fit. Seating and squeezing the rivets on these hinges is a bit tricky and you will need to use the close quarter riveter which just barely fit in.
This is the hinge in the middle of the wing. The dark green spots are from primer to cover up nicks from the manual riveter and to cover up the rivets themselves (while I was at it).
Finally I put the top skins in place to see how the wing looks like and also to cover the interior from excessive dust (there's another storm forecast for tomorrow).
Looks almost like a wing now!
Subscribe to:
Posts (Atom)
